Exam Prep app › ASE-style practice tests: A1 to A9 and G1
Practice questions with explained answers
ASE-style practice tests: A1 to A9 and G1
943 practice questions, each with an explanation of why the right answer is right and where the rule comes from. Try 10 of them below; the rest are in the CostPerCover Exam Prep app for iPhone, iPad and Android.
Free sample of every test. Unlocking all 10 tests is a one-time purchase ($29.99 in the U.S.), with no subscription.
Try 10 questions
Pick your answer first, then open the answer to see why.
Question 1 · A1 Engine Repair · General Engine Diagnosis
An engine puffs blue-gray smoke for a few seconds after a cold start, then the smoke clears. What is the most likely cause?
- Worn valve stem seals or guides
- A leaking head gasket or cracked head
- Rich cold-start fuel enrichment
- Condensation in the exhaust system
Show the answer
Answer: A. Worn valve stem seals or guides
Oil seeps past worn stem seals or guides into the cylinders while the engine sits and burns off at startup, then the smoke clears. Constant blue smoke under load points more toward rings. Coolant from a head gasket leak or cracked head makes white vapor, as condensation does, and rich running makes black smoke.
Source: ASE A1 task list, area A: General Engine Diagnosis
Question 2 · A2 Automatic Transmission/Transaxle · Transmission/Transaxle Diagnosis
A transmission with a dipstick is being checked for fluid level and condition.
Technician A says: Most transmissions should be checked with the engine off and the fluid cold.
Technician B says: Dark fluid with a burnt smell indicates overheated friction material.
Who is right?
- A only
- B only
- Both A and B
- Neither A nor B
Show the answer
Answer: B. B only
Most dipstick units are checked hot, with the engine idling in Park (or Neutral) on level ground, or exactly as the manufacturer specifies. A cold mark on the dipstick is only a rough check, so A is wrong. A burnt smell, especially with dark fluid and friction material in the pan, means clutches or bands have overheated, so B is right. Color alone is not enough, because some fluids darken in normal service.
Source: ASE A2 task list, area A: Transmission/Transaxle Diagnosis
Question 3 · A3 Manual Drive Train & Axles · Clutch Diagnosis and Repair
A manual transmission makes noise with the engine running.
Technician A says: A noise heard only while the clutch pedal is pressed points to the input shaft bearing.
Technician B says: A noise in neutral that goes away when the pedal is pressed points to the release bearing.
Who is right?
- A only
- B only
- Both A and B
- Neither A nor B
Show the answer
Answer: D. Neither A nor B
They have it backwards. The release bearing is loaded only while the pedal is pressed. A noise in neutral that stops when the pedal is pressed comes from the input shaft or countershaft bearings, which stop turning once the clutch releases.
Source: ASE A3 task list, area A: Clutch Diagnosis and Repair
Question 4 · A4 Suspension & Steering · Steering Systems Diagnosis and Repair
Two technicians are discussing electric power steering (EPS).
Technician A says: The EPS module uses a steering torque sensor input to decide how much assist to give.
Technician B says: Low system voltage can reduce or disable the assist.
Who is right?
- A only
- B only
- Both A and B
- Neither A nor B
Show the answer
Answer: C. Both A and B
The torque sensor tells the module how hard the driver is turning. EPS motors draw high current, so the module reduces assist when voltage is low.
Source: ASE A4 task list, area A: Steering Systems Diagnosis and Repair
Question 5 · A5 Brakes · Hydraulic, Power Assist, and Parking Brake Systems Diagnosis and Repair
A spongy brake pedal is most likely caused by:
- Air in the brake hydraulic system
- A vacuum leak at the brake booster
- Glazed brake pads and rotors
- Excessive rotor lateral runout
Show the answer
Answer: A. Air in the brake hydraulic system
Air compresses and brake fluid does not, so air in the lines makes the pedal feel soft and springy. Bleed the system following the manufacturer's procedure. A booster leak or glazed pads make the pedal hard, and runout causes pulsation.
Source: ASE A5 task list, area A: Hydraulic, Power Assist, and Parking Brake Systems Diagnosis and Repair
Question 6 · A6 Electrical/Electronic Systems · General Electrical/Electronic System Diagnosis
Two technicians are discussing wiring repairs.
Technician A says: A splice in an area exposed to moisture should be sealed with adhesive-lined heat-shrink tubing.
Technician B says: When splicing twisted-pair data bus wires, untwist at least 6 inches of each wire to make the repair easier.
Who is right?
- A only
- B only
- Both A and B
- Neither A nor B
Show the answer
Answer: A. A only
Adhesive-lined heat shrink seals out water and corrosion, so A is correct. Twisted-pair bus wires should stay twisted as close to the splice as possible because untwisting them makes the bus open to electrical noise, so B is wrong.
Source: ASE A6 task list, area A: General Electrical/Electronic System Diagnosis
Question 7 · A7 Heating & Air Conditioning · HVAC and Engine Cooling System Service, Diagnosis, and Repair
Two technicians are discussing R-1234yf systems.
Technician A says: R-1234yf is classified as mildly flammable (A2L).
Technician B says: R-1234yf requires its own dedicated recovery and charging equipment.
Who is right?
- A only
- B only
- Both A and B
- Neither A nor B
Show the answer
Answer: C. Both A and B
R-1234yf is an A2L (mildly flammable) refrigerant, so A is correct. It has its own service fittings and needs SAE J2843 recovery/recycling/recharging equipment with a built-in or connected refrigerant identifier, so refrigerants do not get mixed. B is correct too.
Source: ASE A7 task list, area A: HVAC and Engine Cooling System Service, Diagnosis, and Repair
Question 8 · A8 Engine Performance · General Diagnosis
A relative compression test is done by watching starter current on a lab scope while the engine is cranked with fuel and spark disabled. One current hump is noticeably smaller than the others. This indicates:
- Low compression in one cylinder
- A weak battery
- A faulty starter motor
- One cylinder with excessive compression
Show the answer
Answer: A. Low compression in one cylinder
The starter draws more current to push each piston through its compression stroke. A smaller hump means that cylinder offers less resistance, so its compression is low.
Source: ASE A8 task list, area A: General Diagnosis
Question 9 · A9 Light Vehicle Diesel Engines · General Diagnosis
A turbocharged diesel makes a loud hiss or whistle that rises with engine load. The scan tool shows actual boost well below desired and the engine has low power. What is the most likely cause?
- A leaking charge air cooler or hose
- A wastegate stuck in the closed position
- A restricted fuel return line or cooler
- A glow plug control module that has failed
Show the answer
Answer: A. A leaking charge air cooler or hose
Pressurized intake air escaping from the charge air system makes a hiss that rises with boost and causes low boost and low power. A wastegate stuck closed causes overboost, and a fuel return restriction or a glow plug module fault does not make a load-dependent hiss or lower boost.
Source: ASE A9 task list, area A: General Diagnosis
Question 10 · G1 Auto Maintenance & Light Repair · Engine Systems
A belt drive chirps at idle, and the automatic tensioner arm is seen bouncing back and forth excessively. What is the most likely cause?
- A worn automatic tensioner
- A glazed belt that needs belt dressing
- Alternator voltage set too high
- A low engine oil level
Show the answer
Answer: A. A worn automatic tensioner
A tensioner with a worn spring or damper cannot hold steady belt tension, so the arm oscillates and the belt slips and chirps. Belt dressing is not a repair, and a glazed belt, charging voltage, or oil level does not make the tensioner arm bounce.
Source: ASE G1 task list, area A: Engine Systems
The test at a glance
A1 Engine Repair, A2 Automatic Transmission/Transaxle, A3 Manual Drive Train & Axles, A4 Suspension & Steering, A5 Brakes, A6 Electrical/Electronic Systems, A7 Heating & Air Conditioning, A8 Engine Performance, A9 Light Vehicle Diesel Engines, G1 Auto Maintenance & Light Repair
| Test | Questions in the app | Simulation length | Time |
|---|
| ASE-style A1 Engine Repair test | 90 | 55 | 75 min |
| ASE-style A2 Automatic Transmission/Transaxle test | 90 | 55 | 75 min |
| ASE-style A3 Manual Drive Train & Axles test | 80 | 50 | 60 min |
| ASE-style A4 Suspension & Steering test | 80 | 50 | 60 min |
| ASE-style A5 Brakes test | 90 | 55 | 75 min |
| ASE-style A6 Electrical/Electronic Systems test | 100 | 60 | 90 min |
| ASE-style A7 Heating & Air Conditioning test | 100 | 60 | 75 min |
| ASE-style A8 Engine Performance test | 100 | 60 | 75 min |
| ASE-style A9 Light Vehicle Diesel Engines test | 103 | 60 | 75 min |
| ASE-style G1 Auto Maintenance & Light Repair test | 110 | 65 | 90 min |
Current to: A1 task list in the 2026 ASE Automobile Study Guide
Keep practicing in the app
- Every answer explained, with the law, code or outline it comes from
- Tap Sure, Unsure or Guess first: questions you were sure about but missed come back first
- Full-length timed simulations in the test’s format and topic mix
- A readiness range for each topic, and a study plan that counts down to your test date
- Works offline. No account and no ads
Free sample of every test. Unlocking all 10 tests is a one-time purchase ($29.99 in the U.S.), with no subscription.
Where the questions come from
Independent practice questions. Not affiliated with or endorsed by the National Institute for Automotive Service Excellence (ASE). The questions are our own practice questions, not questions from the real test.